Owon MSO Series Manuel d'utilisateur Page 80
- Page / 112
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
75
CH00～CH0F
Don't Care
Low
High
No trigger occurs.
Trigger occur when signal on the low level
Trigger occurs when signal on the high level.
To observe the 16 channel data need to know how data changed before and after when
"BIT0-BIT3" STATE is "0111".
A. Press "Trigger menu" and menu appears.
B. Press "F1" till trigger mode display as "Pattern"
C. Press "F2" or turn "CH1 Volts/div" knob till "CH SEL" display as "CH00"
D. Press "F3" till F3 window display as "CH00/High" and "CH00" in F2 window display
as "1".
E、Repeat operation of step D and set CH01, CH02 to "High" and CH03 as
"Low",CH04~CH0F set as "Don't care".
Pattern trigger setting finished (refer to Fig.5-59) and ready for data acquisition.
Fig.5-59：Pattern trigger
4． Sequential queue trigger: make BUS as trigger source and continuous setting data in
BUS as trigger condition to generate trigger and also can set 8 data at the same time.( See
Fig.5-60)
- MSO Series 1
- User Manual 1
- Headquarter: 2
- Branch: 2
- General Warranty 3
- Table of Contents 4
- Safety Terms 7
- Safety Symbols 7
- Warning: 8
- 3. General Characteristics 9
- 4. Junior User Guidebook 10
- Front panel 11
- Control(key and knob) area 12
- User interface introduction 14
- 4.3 Logic Analyzer 23
- How to acquire data 24
- Display systems 25
- Trigger system 26
- Threshold voltage system 27
- Sampling system 28
- Fig. 4-19 29
- 5. Advanced User Guidebook 30
- Input signal is interrupted 31
- Using FFT function 35
- Knobs 40
- Main Time Base 41
- Set Window 41
- Zone Window 42
- How to set trigger system 43
- Single trigger 44
- Video Trigger 45
- Pulse Width Trigger 46
- Alternate trigger 47
- Menu is shown as Fig.5-23 48
- Menu list: 48
- Pulse) Menu 49
- Pulse) menu list 50
- Slope )Menu 50
- Slope) menu list: 50
- waveform 54
- Persist 55
- XY Format 55
- Save a waveform 57
- Recall a stored waveform 57
- Fig.5-38 Wave Saving 58
- Fig.5-39 FFT wave saving 58
- SYS STAT (System State) 59
- CURS MEAS Menu 65
- MATH FFT 65
- How to use Autoscale 67
- Fig.5-51 68
- RUN/STOP 69
- U-DISK COPY 69
- Figure: Reload Disk 72
- Figure: Choose format 72
- Figure: Format setting 72
- Figure: Apply setting 73
- Figure: Format process 73
- Figure: Format successfully 73
- 5.2 Logic analyzer 74
- Low memory 75
- Fig.5-56 77
- Fig.5-56：Bus trigger menu 78
- Fig.5-57) 78
- Fig.5-57：Bus trigger 79
- Fig.5-58) 79
- Fig.5-59：Pattern trigger 80
- Fig.5-60) 80
- Fig.5-61) and data ready for 82
- Fig.5-62 82
- How to set threshold 84
- Fig.5-66 85
- How to set display system 86
- How to set BUS 87
- Fig.5-70：Bus menu 88
- Fig.5-71) 88
- How to measure 89
- How to save and recall 89
- Fig.5-73 90
- Fig.5-73.：Storage menu 90
- Fig.5-74) 90
- How to search 91
- Fig.5-76.：Search Bus 93
- How to review setting info 94
- How to set Utility 97
- 6. Demonstration 98
- Metering Circuit 99
- 7. F.A.Q 105
- Digital Storage Oscilloscope 106
- Logic analyzer 109
- 9. Appendix 111
Produits connexes et manuels pour Instruments de mesure Owon MSO Series
(88 pages)Crimestopper Security Products EZ-31DP manuels
Manuels d'utilisation et guides de l'utilisateur pour Alarme de voiture Crimestopper Security Products EZ-31DP.
Nous fournissons des manuels en pdf 1 Crimestopper Security Products EZ-31DP à télécharger gratuitement par type de document : Manuel de l'utilisateur
Commentaires sur ces manuels